Renaultman V4.10 CAN/K-Line Immo Tool, OBD2 Programmer, EEPROM R/W

Renaultman V4.10 CAN/K-Line Immo Tool, OBD2 Programmer, EEPROM R/W

Important tips:

The hardware is purchased, and the software is free.

Renault ecu tool v4.10 software can be used, but only some functions are 4.10. The original factory did not develop all the functions of 4.10 software, but 4.08 and 4.09 software support most functions.

If you can’t accept it, please do not buy it!!!FOR Renaultman C-AN/K-line ECU Tool

OBD2 tool with various for Ren-ault car electronic control unit internal memory modification functions, such as Re-ad/Wri-te EEPROM or FLA-SH, Clear Immobilizer Code, Re-ad Immobilizer Status and Program Cards.

There is no need to open control unit, de-solder memory IC or connect any wires directly to it. All functions works by OBD2 connector, but any supported control unit can be connected “on the bench” using Connection Manual.

Clear Immobilizer Code function is fully automated – just press button and control unit will be cleared. ECU is ready to accept new immobilizer code after previously programmed code is cleared – no future programming is required.

This in not a tool for a TOTAL immobilizer disabling. It only clears previously memorized immobilizer code to give ability of using second-hand Engine control Unit (ECU) in particular car or make simple data cloning from one ECU to another.

Software  supports:

· ABS/ESP (ATE) for X91/X95/X38/L70 – EEPROM R/W, Chan-ge VIN, Chan-ge KM by OBD2
· Automatic parking brake (TRW) for X95/X38 – R/W Config, Chan-ge VIN, set maintenance mode for breakpad replace  (NEW !)
· EDC17 / SID305-310 / DCM3.4 / EMS31XX MILEAGE REPAIR by OBD II
· EDC15C3 (both for CAN-BUS and WIRE immo systems) – R/W EEPROM, R/W FLA-SH, Clear Immo Code
· EDC15C13  – R/W EEPROM, R/W FLA-SH, Clear Immo Code
· FOR SIRIUS 31H  – R/W EEPROM, R/W FLA-SH, Clear Immo Code
· FOR SIRIUS 32[N] (both for CAN-BUS and WIRE immo systems) – R/W EEPROM, R/W FLA-SH, Clear Immo Code
· FOR SIRIUS 34 (both for CAN-BUS and WIRE immo systems) – R/W EEPROM, R/W FLA-SH, Clear Immo Code
· FOR SIRIUS 35  – R/W EEPROM, R/W FLA-SH, Clear Immo Code
· EMS3132 (both for CAN-BUS and WIRE immo systems) – R/W EEPROM, R/W FLA-SH, Clear Immo Code
· EMS3134 (both for CAN-BUS and WIRE immo systems) – R/W EEPROM, R/W FLA-SH, Clear Immo Code
· SID301 – R/W EEPROM, R/W FLA-SH, Clear Immo Code, Clear IMPACT DETECTED, R stored mileage
· SIM32 – R/W EEPROM, R/W FLA-SH from HD64F7055, Clear Immo Code
· SAFIR / SAFIR2 / SFR200 (35 / 55 pin connector) – R TMS374 EEPROM, Clear Immo Code (carruns without immobilizer code)
· IAW 6R.20 – R/W TMS370 EEPROM
· IAW 6R.30 – R TMS370 EEPROM, Clear Immo Code  (car runs without immobilizer code)
· for VALEO BII for  for ESPACE III – R/W (9)08AZ60 EEPROM, R/W mileage, Clear for Replacement, R transponder data, Emergency Startup
· for VALEO IMMOBILIZER for  for LAGUNA I Ph2 (1998-2000) – R transponder data, Configure, Re-set to VIR-GIN
· for VALEO IMMOBILIZER for  for LAGUNA I Ph1 / SAFRANE Ph1 (1995-1996) – R PINCODE, Re-set to VIR-GIN
· for INSTRUMENT CLUSTER for  for ESPACE III (1998-2002) – Re-set odometer, Erase RF remote programming  by instrument cluster connector
· Sie-mens IMMOBILIZER for  for ESPACE III Ph1 (1996-1998) – R/W 68HC05B16 EEPROM, R transponder data
· for INSTRUMENT CLUSTER for ESPACE IV Ph1 (’03-’04) K-Line – Chan-ge language and units, Chan-ge VIN, KM, R/W EEPROM
· for INSTRUMENT CLUSTER for ESPACE IV Ph2-Ph4 (‘2005+) CAN- Chan-ge language and units, Chan-ge VIN, KM, R/W EEPROM
· Sie-mens UCH for MEGANE/SCENIC I Ph2 (’99-’02) – R/W 705B32 EEPROM, R/W configuration, Learn Keys, Re-set to VIR-GIN
· Sie-mens UCBIC for MEGANE/SCENIC I Ph1 (’96-’98) – R/W 68HC05B16 EEPROM, R/W configuration, Resest to VIR-GIN
·  for LAGUNA II,  for ESPACE IV, VELSATIS Ph1/Ph2 – Key-Card Programming, Chan-ge VIN. Re-set UCH to VIR-GIN, Learn UCH
·  for MEGANE II, SCENIC II Ph1/Ph2 – Card/UCH/ECM/ESCL Learning, Chan-ge VIN, Re-set UCH to VIR-GIN, Config TPMS
· INSTRUMENT CLUSTER for SCENIC II (’04-’08) – Wake-Up by CAN-BUS for repair or to check mileage, Chan-ge language and units, Chan-ge VIN, KM, R/W EEPROM
· INSTRUMENT CLUSTER for  for MEGANE II (’03-’08) – Wake-Up by CAN-BUS for repair or to check mileage, Chan-ge language and units, Chan-ge VIN, KM, R/W EEPROM
·  for C-LIO II Ph1 – Key Learning, Configuration, Re-set BMT to VIR-GIN
·  for C-LIO II Ph2-5, for KANGOO,  for TRAFIC, for MASTER, for VIVARO, for MOVANO (-’07) – R/W EEPROM 93C66, Key Learning, Chan-ge VIN, Re-set UCH to VIR-GIN, Learn UCH
·for KANGOO I,  for TRAFIC, MASTER, VIVARO, MOVANO (’07-) – Key Learning, Chan-ge VIN, Re-set UCH to VIR-GIN, Learn VIR-GIN UCH
· for KANGOO II (2007-2012) – Key Programming, Chan-ge VIN, Re-set BCM to VIR-GIN, Learn VIR-GIN BCM
· for MODUS /  for C-LIO III ELECTRIC POWER ASSISTED STEERING (for TRW DAE/for PAS) – Clear Immo Code, Chan-ge VIN by OBD2, erase DF002 from 24C16 dump, repair CRC
·  for MEGANE/SCENIC III ELECTRIC POWER ASSISTED STEERING (for NSK DAE/for PAS) – Clear Immo Code, Chan-ge VIN by OBD2
·  for MEGANE/SCENIC IV (2016+) ELECTRIC POWER ASSISTED STEERING (for NSK DAE/PAS) – Clear Immo Code, Chan-ge VIN by OBD2
· TWINGO III ELECTRIC POWER ASSISTED STEERING (for JTEKT DAE/PAS) – Clear Immo Code, Chan-ge VIN by OBD2
·  for ESPACE V / for TALISMAN / for SAMSUNG SM6 ELECTRIC POWER ASSISTED STEERING (for TRW EPS) – Clear Immo Code, Chan-ge VIN by OBD2
·  for C-LIO IV ELECTRIC POWER ASSISTED STEERING (for JTEKT DAE/PAS) – Clear Immo Code, Chan-ge VIN by OBD2
·  for LAGUNA III (2007-2015) – KeyCard Programming, Chan-ge VIN, Re-set BCM to VIR-GIN
·  for LAGUNA III / LATITUDE (2007-2015) – Learn BCM / ECM / ESCL in protected mode
· LATITUDE (2010+) – KeyCard Programming, Chan-ge VIN, Re-set BCM to VIR-GIN
·  for C-LIO III / MODUS – Key Programming, Chan-ge VIN, Learn ECM in protected mode, Learn BCM, Re-set BCM to VIR-GIN
·  for C-LIO III – Card/UCH/ECM/ESCL Learning, Chan-ge VIN, Re-set UCH to VIR-GIN
·  for C-LIO IV (2012+)- Card Programming, Chan-ge VIN, Re-set HFM to VIR-GIN, Learn ECM / ESCL/HFM in protected mode
· MASTER III (2010-2014) – Key Programming, Chan-ge VIN, Re-set BCM to VIR-GIN, Learn VIR-GIN BCM
·  for TRAFIC II Ph3 (2010-2014) – Key Programming, Chan-ge VIN, Re-set BCM to VIR-GIN, Learn VIR-GIN BCM
· for WIND (2010-2013) – Key Programming, Chan-ge VIN, Re-set BCM, Learn ECM, Learn BCM
·for TWINGO II (2007-2013) – Key Programming, Chan-ge VIN, Re-set BCM, Learn ECM, Learn BCM
·for  TWINGO (2001-2006), for LOGAN (2004-2008), for SANDERO I, for THALIA, for SYMBOL – Key Programming, Chan-ge VIN
· for LOGAN, for SANDERO, for THALIA, for SYMBOL (2008-2012), for Duster (2010-2012) – Key Programming, Chan-ge VIN
· for LOGAN, for SANDERO,for DOKKER, for SYMBOL, for DUSTER (2012+) – Key/ECM/BCM learning, Re-set to VIR-GIN, R DataFLA-SH, Chan-ge VIN
·  for MEGANE III / SCENIC III (2009-2015) – Card Programming, Chan-ge VIN, Re-set BCM to VIR-GIN
·  for MEGANE III / SCENIC III (2009-2015) – Classical Key Programming, Chan-ge VIN, Re-set BCM to VIR-GIN
·  for MEGANE III / SCENIC III / for FLUENCE (2009-2015) – Learn BCM / ECM / ESCL in protected mode. Config TPMS
· for KOLEOS (2008+) – KeyCard Programming, Chan-ge VIN, Re-set BCM to VIR-GIN, Learn ECM/BCM/ESCL
· EDC17 / MED17 TRICORE EEPROM DUMP CRC – Re-set EEPROM dump to VIR-GIN, repair block CRCs
· EDC17 / MED17 TRICORE TC1793 EEPROM DUMP CRC – Repair block CRCs
· EDC16 EEPROM DUMP CRC – Re-set EEPROM dump to VIR-GIN, repair block CRCs  (IMPROVED !)
· DELPHI DCM 3.4 EEPROM DUMP CRC – Re-set EEPROM dump to VIR-GIN, Chan-ge KM, repair block CRCs
· for DECRYPT ISK FROM ECM DUMP – Get ISK from ECM for VIR-GING BCM learning when original BCM is missing
· SID305/306/307/308/309 for TRICORE DFLA-SH DUMP CRC – Search/Chan-ge KM, repair block CRCs
·  for MEGANE III / SCENIC III / FLUENCE / LATITUDE AIR-BAG (for CONTINENTAL) – Erase CRASH DATA by OBD2 / direct connection
·  for LAGUNA III AIR-BAG (AUTOLIV RC5) – Erase CRASH DATA by OBD2 / direct connection
· TWINGO II (X44) / KANGOO II (X61) AIR-BAG (for CONTINENTAL) – Erase CRASH DATA by OBD2 / direct connection
· MASTER III / for MOVANO-B /  for C-LIO III Ph2 /for MODUS Ph2 AIR-BAG (for AUTOLIV) – Erase CRASH DATA by OBD2 / direct connection
· AIR-BAG MODULE WITH SPC560 MCU (for CONTINENTAL) – Erase CRASH DATA by OBD2 / direct connection
·  for MEGANE II / SCENIC II AIR-BAG (for AUTOLIV ACU4) – Erase CRASH DATA by OBD2 / direct connection
·  for C-LIO II X65 AIR-BAG (for BOS-CH AB8) – Erase CRASH DATA, R/W MCU internal EEPROM by OBD2 / direct connection
·  for C-LIO III Ph1 / MODUS Ph1 AIR-BAG (for BOS-CH AB9.X) – Erase CRASH DATA, Erase fault codes by OBD2 / direct connection
·  for ESPACE III AIR-BAG (Sie-mens) – Erase CRASH DATA, R/W MCU internal EEPROM by OBD2 / direct connection
· for LOGAN X90 / for DUSTER H79 AIR-BAG (TEMIC-for CONTINENTAL) – Erase CRASH DATA, R EEPROM by OBD2 / direct connection
· for LOGAN X90 AIR-BAG (for BOS-CH AB8.X with yellow connector) – Erase CRASH DATA, R/W MCU internal EEPROM by OBD2 / direct connection
· for KADJAR / TALISMAN AIR-BAG (for AUTOLIV AC7 with MCU XC2336) – Erase CRASH DATA by OBD2 / direct connection. R full FLA-SH
·  for C-LIO IV Ph2 / CAPTUR Ph2 AIR-BAG (for CONTINENTAL 985100475R, 985101180R, 985103419R with R7F7010133) – Erase CRASH DATA by OBD2 / direct connection